Browse all practice questions for the NOCTI Auto Body Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

NOCTI Auto Body Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Before applying any topcoat material, the vehicle surface must meet which condition?
  • The anchoring system should be attached to how many locations on the vehicle?
  • Which action will help lighten a metallic color?
  • Unibody vehicles seldom incur ___ damage.
  • If the refinish labor was $35 per hour and it took 10.8 hours, what is the total amount for refinish labor?
  • Which type of plastic becomes permanently set and cannot be remelted after curing?
  • Damage that occurs at the point of impact is called
  • Calculate the total sheet metal labor cost for 13.2 hours at 50 per hour.
  • In an auto body shop, which container is most appropriate for storing flammable solvents?
  • What is the primary purpose of shielding gas in MIG welding?
  • In damage assessment, air bag deployment is categorized as which type of damage?
  • If shielding gas flow is insufficient, which weld defect is most likely?
  • A windshield has cracked due to a tree limb striking it. This is known as ____ damage.
  • Ohm's Law refers to which three electrical terms?
  • Resistance is
  • To lighten a metallic color, what adjustment should be made to air pressure?
  • Use a shade lens of ___ or higher for MIG welding
  • Which action should be performed to prepare the surface before applying color coats?
  • During vehicle repair, which welding method is most often recommended for high-strength steel?
  • If the quoted estimate for 15 hours of mechanical labor was $1087.50, the actual cost of 13.5 hours is
  • The recommended container for flammable materials is which type?
  • The 8 percent tax on parts: What is the tax amount added to the parts if the parts cost is 1218.50?
  • Which agency issues environmental safety guidelines?
  • If the basecoat color is too dark, what should the painter do?
  • Which surface property is essential for mixing plastic filler?
  • In an auto shop, which container is recommended for solvent storage?
  • Where should the work or ground clamp be attached to prevent current from passing through mechanical or electrical parts?
  • Clogged spray booth filters will cause which finish defect?
  • What is the final grit in the sanding sequence for a plastic bumper area repaired with a flexible bumper repair kit?
  • What type of sealer should be used on seams that might be exposed to automotive fluids?
  • The most commonly recommended shielding gas for auto body MIG welding on steel includes a mixture of carbon dioxide and ______.
  • Which type of glass is commonly used in vehicle windshields?
  • For MIG welding of steel, what flow rate range is recommended for shielding gas?
  • A metallic color sprayed wet will:
  • When making a vertical butt weld, from which end should the weld be started?
  • What is another common method to confirm a vehicle's factory color?
  • Before applying the color coats, which action should be performed on the old finish?
  • Automotive fuses are rated in
  • Mash damage is
  • When labeling flammable liquids for storage, which container type is preferred?
  • For storage compliance, flammable liquids should be kept in which container?
  • Before refinishing operations, what should the technician use to wash the vehicle surface?
  • What type of respirator must be used when spraying paints that contain a hardener or catalyst?
  • Mash damage is defined as
  • Which statement describes the structural role of the windshield in most vehicles?
  • Excessive use of hammer and dolly will often ____ the metal
  • What is the purpose of metal conditioner in prep work?
  • Tempered glass is true about tempered glass compared with laminated glass?
  • When using a bench grinder, which eye protection must be used?
  • To raise a door that is sagging at the rear (hitting the striker), where should the upper hinge be moved?
  • Electrically powered tools with damaged or worn cords must
  • What paint-to-thinner ratio is recommended to reduce paint by 150 percent?
  • In the given example, tax is applied to which portion of the total?
  • The pressure of force of electricity is known as
  • Which of the following should be stored in metal containers for safety
  • A dual-action sander is used to
  • What is described as the proper spray technique?
  • When replacing a fender on an undamaged vehicle, starting at the cowl area helps ensure proper fit of adjacent panels. This statement is
  • Which type of glass is used for windshields?
  • What type of glass strengthens a vehicle's body structure?
  • The hourly rate implied by a refinishing job that costs $378.00 for 10.8 hours is which of the following?
  • What is the correct initial action when servicing a vehicle's air conditioning system that uses refrigerant?
  • Laminated glass is made by encapsulating which material between two layers of glass?
  • In the event of wind noise near a door after maintenance, which items should be inspected?
  • What is the proper sanding sequence for a plastic bumper area repaired with a flexible bumper repair kit?
  • Which section of the MSDS explains how to treat a worker who has been overexposed to a material?
  • The labor amount in the total of 2469.30 if parts cost 1126.30?
  • An example of secondary damages is a ______.
  • The starting reference used when aligning panels around the front of a vehicle is usually the
  • What is used to correctly repair Sheet Molded Compound (SMC) panels?
  • When spray painting, each stroke should overlap the preceding stroke by at least what percentage?
  • What is the cost of parts before tax in the scenario where parts cost is 1218.50 and tax on parts is 97.48?
  • When using a floor jack, a technician should always use
  • Bumper reinforcements may be straightened under which condition?
  • Which of the following is another name for the cartridge filter respirator?
  • Sheet Molded Compound (SMC) panels are correctly repaired using which bonding method?
  • Which container type reduces risk of static ignition during handling of flammable liquids?
  • Why is moisture avoidance in the air line important during priming bare steel?
  • Flammable liquids should be stored in what type of container to reduce the risk of sparks and leaks?
  • What is the manufacturer's recommended tool for removing factory spot welds?
  • If an energy absorber has collapsed in a collision, what is the recommended action?
  • Automotive electrical systems are what types of current?
  • A Safety Data Sheet (SDS) provides information on proper handling and storage, product reactivity, and
  • Which sealer is specified for seams exposed to automotive fluids?
  • What shielding gas composition is most commonly used for autobody MIG welding on steel?
  • Which statement is true about the anchoring system?
  • To safely support a vehicle after lifting with a floor jack, you should always use
  • When does the chemical reaction between clearcoat and catalyst begin?
  • What is the minimum stroke overlap in spray painting?
  • R & R on the estimate sheet means
  • Which combination is required for corrosion to occur?
  • What is the basic starting requirement for any effective repair process?
  • Indirect damage is
  • The ___ angle is the inward or outward tilt of the tire measured at the top.
  • Current US laws require which of the following regarding refrigerants?
  • Water should be drained from the air compressor storage tank how often?
  • The C-pillar is located between which two panels?
  • Which statement about applying the second coat of basecoat is true?
  • Bird-nesting in a MIG welding setup most commonly occurs between the drive rollers and liner.
  • For MIG welding, which shade level is the minimum recommended?
  • Why should the vehicle's electrical system be disconnected during welding?
  • Laminated glass is typically used for which automotive component?
  • The collision repair shop is responsible for hazardous waste generated in which circumstances?
  • Which statement about eye protection when using a bench grinder is true?
  • What term describes plastic parts that can be reshaped by heating?
  • The cost of a repair is $1218.50 for parts and $2517.48 for labor. With 8 percent sales tax added to the parts, the total cost is
  • Another name for the cartridge filter respirator is which of the following?
  • When the front wheels of a vehicle are closer at the front and further at the rear, this is known as
  • In safety data documentation, which section provides guidance on treating overexposure to a chemical?
  • To verify proper weld penetration, which indication on the reverse side should the technician inspect?
  • With the engine running, how much voltage should be across the battery terminals?
  • How long should a new topcoat be allowed to cure before applying automotive finish wax?
  • Which action warns against burns when interacting with a hot cooling system component?
  • The quoted labor estimate for a repair was 12 hours and $935.50. If the actual repair took 11 hours, the final labor cost is?
  • Which device in electrical systems uses a small current to control a larger current?
  • Where should plastic filler be mixed?
  • What is the proper handling of anti-theft labels during service?
  • Which container type is advised for safe storage of flammable solvents in a shop setting?
  • How does increasing the gun movement speed affect color?
  • What is the most typical recommended hole size for structural MIG plug weld?
  • The repair total is $2469.30. Parts cost $1126.30. What percent of the total cost is labor?
  • The term 'R & I' means
  • When using a battery charger, the technician should
  • What angle might cause pull without causing tire wear?
  • Which statement best describes the recommended spray technique?
  • Which device is used to measure voltage?
  • Removing adhesive attached body side moldings requires the use of which tools?
  • To replace a damaged AC compressor, the first step should be to
  • When installing a new door on a vehicle, the technician should
  • The roof support on either side of a car's windshield is referred to as the ______.
  • If a door area has wind noise, which two components are most critical to inspect?
  • Which shielding gas mix is most commonly used for autobody MIG welding on steel?
  • Which glass type is formed by heating and cooling to increase its strength and is commonly used in windshields?
  • If structural adhesive joints have been disturbed, what repair method is recommended?
  • Which option should be used to transport flammable solvents in a work area if metal storage is chosen?
  • When working on a vehicle's cooling system, which component requires caution when opening to avoid burns?
  • Using Ohm's Law, how much current is going through the following circuit: 12.6 volts, 10 Ohms resistance
  • Which container is considered best practice for flammable liquids in a maintenance bay?
  • Federal guidelines concerning the safety of the environment are issued by which agency?
  • When putting out a fire involving oily rages, use a ____ fire extinguisher
  • The section of the MSDS that explains what conditions, such as heat or shock, make the hazardous material unstable is
  • A tire worn in a saw-tooth edge pattern indicates improper ____ adjustment.
  • The cost of a repair is $1450.00 for parts and $2689.75 for labor. With 7 percent sales tax added to the parts, what is the total cost?
  • Which initial step is required when replacing a damaged AC compressor?
  • Which device is used to measure resistance?
  • In installing a new door on a vehicle, what is the correct sequence?
  • In unibody construction, which type of damage is uncommon?
  • Which formula represents Ohm's Law for calculating current?
  • Work time and full cure time of most adhesives are calculated at what temperature?
  • After disassembly, the next step in the sequence of operations for a structural panel replacement is to ______.
  • During initial door alignment, which component should be removed?
  • When servicing McPherson struts, always use
  • After a head-on collision, a buckle in the roof indicates what type of damage?
  • To locate wind noise or water leaks near a door, which components should be inspected?
  • The voltage drop across a large resistance in a circuit will be
  • During welding operations, what should be done with the ground cable or battery cables to protect the vehicle's computers?
  • Which statement best describes the proper action when exhaust components are damaged?
  • In a McPherson strut suspension, which component mounts on the outer end of the control arm?
  • What must be done when exhaust system components are damaged on a late model vehicle?
  • Steering suspension components have been replaced on the front of a vehicle. The technician must perform a
  • Compared with conventional primers, chip resistant coatings are:
  • Which weld process uses no consumables?
  • Arc (ultraviolet) radiation created by welding can
  • Installing a larger diameter contact tip in a squeeze-type resistance spot welder will ____ of the spot weld.
  • In structural MIG plug welds, what is the most typical hole size?
  • Wheel lugs should be tightened with a/an
  • If the shop temperature is low, which reducer or thinner should be used?
  • Under current US law, what is required for refrigerants?
  • Glass with vinyl encapsulated between two layers of glass is
  • Which parts are mounted at the inner end of control arms?
  • Which device is used to measure electrical current?
  • Which statement about MIG welding shielding gas is correct?
  • Dents in padded dashed and other padded interior parts are removed using
  • Which weld process uses no consumables?
  • Air bag deployment is considered which type of damage?
  • What is the recommended container for flammable chemicals in a maintenance area?
  • To prepare a painted panel for refinishing, what action should be performed?
  • A technician is installing a replacement fender on an undamaged vehicle. Adjustments must begin at the
  • What combination of elements is needed for corrosion to occur on metal surfaces?
  • Which class of fire involves flammable liquids?
  • Anti-spatter compound is used during MIG welding to
  • Tempered glass consists of a
  • Which container type is considered best for flammable liquids to prevent ignition?
  • What is the most critical step in straightening a damaged area?
  • A dual-action sander is used to
  • Which component is mounted at the inner end of control arms?
  • For transporting flammable solvents within a shop, store them in which container?
  • Which of the following is a flat surface parallel to the underbody of the vehicle at some fixed distance from the underbody?
  • What measuring approach allows measuring more than two underbody points at once?
  • Which of the following is the safest respirator option when working with isocyanates?
  • Based on the quoted labor estimate of 12 hours for $935.50, the approximate hourly rate is closest to which value?
  • Federal guidelines concerning the safety of workers are issued by which agency?
  • Which grit is specified for wet sanding the entire panel when preparing for pearl basecoat blend?
  • If a door intrusion beam is severely damaged, which manual provides repair guidance?
  • For preparing a panel for a pearl basecoat blend, what wet sanding grit is specified?
  • Bare metal, moisture (electrolyte) and ___ are needed for corrosion to occur.
  • In a workshop, which container type maintains safety when storing flammable materials?
  • What is the basic starting requirement for any effective repair process?
  • Adhesive work time and full cure time are calculated at which temperature?
  • In the unibody structure, what provides the critical mounting positions for the suspension and steering systems?
  • When the engine is running, the battery voltage should be within which range?
  • The chemical reaction between clearcoat and catalyst begins when?
  • What is the first step in preparing a plastic body panel?
  • A/An ___ wrench provides the safest grip on a fastener
  • A technician is replacing an engine cradle in a front-wheel-drive vehicle. The new cradle has one slotted hole. What fasteners are required to complete the installation?
  • Moisture in the air supply to the spray equipment when priming bare steel could cause which problem?
  • For metallic finishes, increasing gun movement speed tends to:
  • Which measuring technique should be used to measure more than two points of the underbody simultaneously?
  • Which feature is designed to deform during a crash to absorb energy?
  • When the bottoms of a car's wheels are closer together than the tops, the car is said to have ___ camber.
  • One of the functions of hydraulic shock absorbers and McPherson struts is to help control
  • Which of the following are removed when using heating techniques?
  • A relay is an electric component that uses a
  • In straightening procedures, what step should be performed first for accuracy?
  • The primary safety reason for storing flammable materials in metal containers is to reduce leakage and ignition risk.
  • A SAE bolt head has 3 slashes or raised marks. These marks indicate a ___ bolt.
  • Plastic parts that are hardened when heated are called
  • What is the difference in cost between the quoted total and the actual cost for 13.5 hours?
  • What is the most accurate way to determine a vehicle's factory color?
  • Voltage drop can be measured
  • An energy absorber that has collapsed because of impact should be
  • When wet sanding a hood, roof, or deck lid, how should the sanding be performed?
  • Laminated glass is used for which component?
  • The repair total is 3833.46. Parts cost 1218.50. What is the labor cost?
  • The term where half of the vehicle (front or rear) is shoved off to one side.
  • Structural adhesive joints disturbed by damage should be replaced using which technique?
  • Air-powered tools such as the dual-action sander and jitterbug will last longer and require less maintenance if they are
  • In MIG welding, which adjustment flattens the welding bead?
  • The term for damage caused by collision energy traveling through the vehicle is
  • Crush zones make a car safer in a collision because they
  • Mold release agents can cause which issue?
  • Which manual provides official repair guidance for major structural components?
  • Adjustable stops are used to control the ____ of panel alignment
  • A four-door vehicle was involved in a frontal impact. Adjust the _____panel assembly first
  • Which practice extends the life of air-powered tools?
  • A buckle in the roof following a frontal impact is typically categorized as which type of damage?
  • To lighten a paint color, which adjustment is recommended?
  • Anti-spatter compound in MIG welding serves primarily to
  • When should weld-through primers be applied in the welding process?
  • On most unibody vehicles, the windshield is considered ___ glass.
  • What is the proper first cleaning agent for preparing a plastic panel?
  • Door glass is attached to the regulator mechanism using
  • Which statement about tempered glass is true?
  • In a frontal collision, which part is commonly damaged as secondary damage due to inertia?
  • When clearing codes, the technician should
  • The C-pillar refers to the section located between which panels?
  • A second coat of basecoat should be applied when the first coat:
  • The most common cause of undercut and spatter is
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy